REDWAY BATTERY / KNOWLEDGE
How does a 48V telecom battery connect to a -48V positive-ground system?

Redway Battery Editorial Team
Talk / Battery Q&A
A telecom contractor is replacing VRLA strings in a -48V base-station cabinet and asks how a “48V” lithium module fits a system where the positive bar is bonded to earth.
Direct answer: A -48V telecom plant is a normal 48V DC system with the positive conductor used as the earthed return. The battery itself does not change: its positive terminal goes to the grounded return bus and its negative terminal goes to the -48V bus through the battery fuse or breaker. What you must confirm is that the battery’s enclosure, BMS communication ports and any internal grounding do not create a second, unintended earth path, and that the charge and cut-off voltages suit the rectifier settings.
The standard. ETSI EN 300 132-2 defines the -48 V DC interface for ICT equipment, with the positive conductor connected to earth and a normal service range of -40.5 V to -57.0 V. Many sites follow this or an operator-specific variant, so read the site power specification before ordering.
Voltage fit. The PM-LV48100-TELECOM lists 54.75V max charge and 37.5V cut-off, which sits around the ETSI service window; set the rectifier float and low-voltage disconnect so the battery is not pushed above its charge limit or drained below the equipment’s minimum.
Wiring polarity. Label bars clearly: “+ / return (0V, earthed)” and “− / -48V”. Connect positive to the return bar first, then the negative through the protection device. Meter-check before closing the breaker; reversed polarity on a rectifier bus can trip or damage equipment.
Enclosure and earthing. Ask whether the battery case is bonded to its negative or isolated. If it is isolated, bond the case to cabinet earth as the site practice requires; if not, confirm with the supplier before mounting it on an earthed rack. See rack battery grounding.
Communication. SNMP, RS485, RS232 or CAN ports reference the battery’s internal ground. When the plant is positive-earthed, check whether the port needs isolation from the controller to avoid ground loops. The PM-LV48150-TELECOM and PM-LV48100-3U pages list the port options; ask Redway engineering for the isolation detail.
Choice of model. For cabinet use, compare the telecom version with a standard rack module in telecom vs standard rack battery.
Commissioning. Record bus voltage, rectifier settings, breaker ratings and battery serials in the site log so the next technician sees the polarity convention.
Changing from VRLA. Lithium modules usually need different float and boost settings from the lead strings they replace, and some rectifiers expect to see battery temperature compensation that a lithium BMS manages internally. Agree the rectifier settings with the supplier before the cut-over, and keep the old strings connected only if the plan explicitly allows mixed chemistries on one bus.
↳ Replying to Redway Battery Editorial Team
Ask for the site DC power specification before quoting so voltage windows and earthing are agreed upfront.
↳ Replying to Procurement perspective
Positive-ground is a site convention; the cell chemistry is unchanged, but case bonding and comms isolation must be confirmed in writing.
↳ Replying to Selection/Engineering perspective
Label return and -48V bars at the battery so service crews never connect by colour assumption.
A -48V telecom plant is a normal 48V DC system with the positive conductor used as the earthed return. The battery itself does not change: its positive terminal goes to the grounded return bus and its negative terminal goes to the -48V bus through the battery fuse or breaker. What you must confirm is that the battery’s enclosure, BMS communication ports and any internal grounding do not create a second, unintended earth path, and that the charge and cut-off voltages suit the rectifier settings.
Verify before ordering: Case bonding, internal grounding and communication-port isolation are not published on the product pages; confirm with Redway engineering. Site operators may use their own variant of the -48V standard.
Sources checked: ETSI EN 300 132-2 V2.8.1.
Editorial Q&A for battery selection and operations. Product figures cited from Redway product pages.
Related products
Related articles & discussions
- How to Choose the Best 48V Lithium Battery for Your Needs
- What’s New In Delta’s Telecom Power Solutions?
- Telecom Lithium Battery vs. Lead-Acid Battery: Which Is Better?
- What Are 48V Forklift Batteries?
- How suitable is a 48V 150Ah Li-ion battery for solar, home, and telecom uses?
- What Are Delta Rectifier Products?
- How Redway Battery Delivers Power and Reliability with 48V LiFePO4 Batteries
- How Many Solar Panels Are Needed for a 48V System?
- How Many Batteries Are Needed for a 48V System?
- What is the Advantage of 48V Battery?
48V 100Ah Telecom Battery
48V 150Ah Telecom Battery
48V 100Ah Server Rack Battery