\n
Tel: +86 189 7608 1534
Tel: +86  (755)  2801 0506
  |  

Get Free Quote

REDWAY BATTERY / KNOWLEDGE

What does Group 31 mean for a 12V lithium battery replacement?

12V 120Ah Lithium Battery factory oem bci group 31

← More Talk discussions

Redway Battery Editorial Team

Talk / Battery Q&A

Buyer question

A boat owner’s old Group 31 deep-cycle battery is failing and they want a 12V lithium replacement that drops into the same box without rebuilding the mount.

Main answerRedway Battery Editorial Team

Main answer

Direct answer: Group 31 is a Battery Council International (BCI) size code that sets the maximum case envelope and terminal style, not the capacity. BCI lists Group 31 at a maximum of about 330 × 173 × 240 mm (13 × 6 13/16 × 9 7/16 in). A lithium battery described as Group 31 should fit inside that envelope, but you still need to check the actual case dimensions, terminal type and position, hold-down method and charger settings before swapping.

Size versus energy. Capacity varies widely inside one group. The 12V 120Ah LiFePO4 page lists 330 × 172 × 215 mm and BCI Group 31, at 1.536 kWh nominal. A smaller 12V 100Ah is listed as Group 24 at 260 × 168 × 210 mm; it will sit in a Group 31 box but needs spacers or a shorter hold-down so it cannot slide.

Terminals. BCI lists Group 31 variants with different posts (31A top post, 31T threaded stud). Redway 12V pages list M8 threaded terminals with T8–T20 options, so plan lugs or adapters rather than clamping a post clamp onto a stud.

Hold-down. Lithium packs are lighter than the lead battery they replace, so a strap tensioned for a heavier case may be loose. Re-tension or pad the box; see mounting in an RV or boat compartment.

Height and lid clearance. A battery box lid needs space for the terminal height plus lugs and boots. Measure from the box floor to the underside of the lid, not just the box sides.

Thin-format alternative. Where the space is tall and narrow instead of Group 31-shaped, the 12V 100Ah EU thin format (395 × 110 × 286 mm) may suit; see where the thin format fits. For Group 24 trays, read Group 24 fit.

Charging and starting. A Group 31 lead battery may have been a dual-purpose starting battery. Confirm whether the lithium model is approved for engine cranking, and set the charger and alternator path for LiFePO4; see charger settings.

Order note. Quote dimensions and terminal type on the purchase order, not just “Group 31”, so the delivered battery matches the space.

Weight and cranking leads. A lithium battery that weighs much less than the lead one may sit lower or shift under the old clamp, so check that the cable lugs still reach without strain. If the old battery fed both the engine and house loads, decide which circuit the new battery will serve before you order.

Selection/Engineering perspective

Reply

↳ Replying to Procurement perspective

BCI group sets the envelope; capacity, terminal style and current rating come from the product table.

Group 31 is a Battery Council International (BCI) size code that sets the maximum case envelope and terminal style, not the capacity. BCI lists Group 31 at a maximum of about 330 × 173 × 240 mm (13 × 6 13/16 × 9 7/16 in). A lithium battery described as Group 31 should fit inside that envelope, but you still need to check the actual case dimensions, terminal type and position, hold-down method and charger settings before swapping.

Verify before ordering: BCI dimensions are maximum overall figures and actual cases run slightly under them. Cranking suitability and terminal torque are model-specific; confirm with Redway.

Sources checked: BCI group size chart (Battery Council International).

Editorial Q&A for battery selection and operations. Product figures cited from Redway product pages.

Related products

Related articles & discussions

redway-power-lithium-battery-engineer

Want a custom offer for lithium batteries? Contact our sales engineers now for A Quick Quote.